Skip to main content
Sign in
Deutsch Español Français Italiano 日本語（日本） 中文 (香港)
Category List
  • Updated

How to Factory Reset SKULLCANDY Headphones

  • Updated
START HERE

How to Factory Reset Skullcandy Headphones or Earbuds

Reset your Skullcandy device if it will not connect, connects to the wrong device, or its earbuds are not working together.

Before you start: Charge your headphones or earbuds before resetting them. Choose your model below.
Crusher ANC / Crusher Evo

Step 1 – Remove the Old Bluetooth Connection

  1. Open Bluetooth Settings on your phone, tablet, computer, or other Bluetooth device.
  2. Find your Skullcandy headphones, then select Forget, Remove, or Unpair.

Step 2 – Reset the Headphones

  1. Make sure the headphones are ON.
  2. Press and hold the top and bottom buttons together for about 2 seconds.
PURPLE flashing + “Disconnected”
Then:
RED & BLUE flashing + “Pairing” = Reset complete and ready to pair
Indy ANC / Indy Evo
Important: Reset both earbuds.

Step 1 – Turn Both Earbuds OFF

Make sure both earbuds are powered OFF.

Step 2 – Reset Both Earbuds

  1. Touch and hold each earbud for about 10 seconds.
  2. Keep holding while the earbuds power cycle ON and OFF again.
Reset complete: Place both earbuds back into the charging case. Then remove them and pair them again.
Push Ultra

Step 1 – Remove the Old Bluetooth Connection

Open your device’s Bluetooth settings and select PUSH ULTRA → Forget / Remove / Unpair.

Step 2 – Turn Both Earbuds OFF

  1. Remove both earbuds from the charging case.
  2. Touch and hold the Power / MFB button on both earbuds for about 6 seconds.

Step 3 – Reset Both Earbuds

  1. With both earbuds OFF, touch and hold the Power / MFB button on both earbuds for about 10 seconds.
  2. Keep holding while they power cycle ON and OFF again.

Step 4 – Sync the Earbuds Together

  1. Put both earbuds back into the charging case.
  2. Wait until both LEDs show RED.
  3. Remove both earbuds from the case.
  4. Wait while they sync with each other.
Both LEDs flash BLUE while syncing.
You will hear a tone when syncing is complete.
Only the LEFT earbud flashing RED & BLUE = Ready to pair
Sesh Evo

Step 1 – Remove the Old Bluetooth Connection

Open your device’s Bluetooth settings and select SESH EVO → Forget / Remove / Unpair.

Step 2 – Turn Both Earbuds OFF

  1. Remove both earbuds from the charging case.
  2. Touch and hold both earbuds for about 6 seconds.

Step 3 – Reset Both Earbuds

  1. With both earbuds OFF, touch and hold each earbud for about 10 seconds.
  2. Keep holding while they power cycle ON and OFF again.

Step 4 – Sync the Earbuds Together

  1. Put both earbuds back into the charging case.
  2. Wait until both LEDs show RED.
  3. Remove both earbuds from the case.
  4. Wait while they sync with each other.
Both LEDs flash BLUE while syncing.
You will hear a tone when syncing is complete.
Only the LEFT earbud flashing RED & BLUE = Ready to pair

Using a different Skullcandy model? Check your Skullcandy user manual for the correct factory reset steps.

Pair with an Avantree Transmitter Again

  1. Put the Skullcandy headphones or earbuds into Bluetooth pairing mode.
  2. Put the Avantree transmitter into Bluetooth pairing mode.
  3. Keep both devices close together and wait for them to connect.
Reset Did Not Work?
  1. Make sure you are following the instructions for your exact Skullcandy model.
  2. For earbuds, reset both the LEFT and RIGHT earbuds.
  3. Hold each button for the full amount of time shown above.
  4. For Push Ultra and Sesh Evo, complete the earbud sync steps after resetting.
  5. Remove the old Skullcandy Bluetooth connection before pairing again.

Still Need Help?

Contact Avantree Support for additional assistance.

Contact Avantree Support

Comments

0 comments

Related articles

Please sign in to leave a comment.